Reader installation

Install guide

Document Number 490-0002-01

Revision 05 – 27th October 2025

941KB

Reader install guide 490-0002-01.pdf

PDF

Open

What’s in the box?

• Accessia Reader

• Bezel removal tool

What you’ll need

• 2 x 3.5mm diameter (no. 6) panhead screws and wall anchors suitable for the wall surface the Reader will be mounted on

• 5-way terminal block with suitable tool for 24AWG wire connection

• Bezel removal tool (supplied)

• 120 Ohm +/- 1% termination resistor (depending on topology)

Mounting guide

Before you start

• Make sure the wall you want to mount the Reader on is flat and vertical

• Choose a good position that is easy for all users to access, including those with limited mobility

• Make sure there is a hole in the wall behind the Reader which you can pass the integrated cable through

• Avoid mounting the Reader directly onto a metallic surface

How to mount the Reader

1. Remove the bezel. Insert the removal tool into the two holes at the bottom of the Reader. Push the tool in until the clips at the lower end of the bezel release and lift. Unhook the upper end of the bezel and remove it from the Reader (Figure 1)

2. Remove the mounting bracket from the back of the Reader by sliding it downwards (Figure 2)

Figure 1: Removing the bezel

Figure 2: Removing the mounting bracket

1. Secure the mounting bracket to the wall using fixings appropriate for the wall surface. Make sure that the that the hole in the wall for the integrated cable and the exit point for the cable from the Reader are lined up when positioning the mounting bracket (Figure 3)

Figure 3: Securing the mounting bracket

1. Pass the integrated cable though the mounting bracket and the wall and then hook the Reader onto the mounting bracket. Make sure the Reader is fully attached to the mounting bracket

2. Hook the top edge of the bezel over the top of the Reader and press the lower end of the bezel until it clicks securely into place

Wiring guide

• The Reader must be connected to an Accessia Hub. For connections and topologies, check the AI Security Hub installation guide and Figure 4 below

• The Reader must be connected using shielded twisted pair cable, for example Belden 8723. Connect the shield to the drain wire in the Reader’s integrated cable

• The RS-485 twisted pair must be terminated at both ends with a 120 Ohm +/- 1% resistor. For details, check the AI Security Hub installation guide

• Make sure that the terminal block and all wiring is inaccessible to unauthorized personnel

Figure 4: Reader integrated cable connections

Maximum cable lengths:

• 22 AWG: 250 feet / 76 meters

• 20 AWG: 330 feet / 100 meters

• 18 AWG: 500 feet / 152 meters

Information

Reader supported credentials

• NFC - MIFARE DESFire EV2 and EV3

• BLE - Accessia for mobile and SDKs

• UWB - Accessia for mobile and SDKs

How to clean

When necessary, clean the Reader with a soft damp cloth. Do not use any solvents or abrasive materials

Compatibility

Readers are only compatible with Accessia Hubs

Software version

Reader software is automatically updated when necessary by the Hub. To check the current software version, check Accessia Installer app or Accessia Portal

Operating conditions

Power input: 8 to 12VDC, 2 Watts maximum

Operating temperature range: -31 to 150ºF / -35 to +66ºC

Humidity: 20 - 90% RH non-condensing

Ingress protection rating: IP65

Impact protection rating: IK07

Compliance

Compliance Model RDR01A

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Contains FCC ID: VPYLB2BP

Contains FCC ID: YCP-32WB5MMGH02